Ford

2005 Powertrain Control/Emissions Diagnosis Villager OBDII

Posted on 20 November 2014

Download 2005 Powertrain Control/Emissions Diagnosis Villager OBDII – Powertrain Control Module The center of the OBD II system is a microprocessor called the powertrain control module (PCM). The PCM has a single 104 pin connector. The PCM receives input from sensors and other electronic components (switches, relays, and others). Based on information received and programmed […] Continue Reading

Comments (0)

Chevrolet

2009 Truck Avalanche Fan Clutch Removal & Installation

Posted on 19 November 2014

Download 2009 Truck Avalanche Fan Clutch Removal & Installation – Installation Procedure 1. Install the fan clutch bolts. 2. Install the fan clutch onto the fan blade. Notice: Refer to Fastener Notice in Service Precautions. 3. Install the fan clutch bolts. ^ Tighten the bolts to 23 Nm (17 ft. lbs.). 4. Install the fan […] Continue Reading

Comments (0)

Chevrolet

1995 Chevrolet Lumina Camshaft Timing Service Procedure

Posted on 19 November 2014

Download 1995 Chevrolet Lumina Camshaft Timing Service Procedure – INSTALL OR CONNECT 1. Camshaft sprockets. ^ 1991-93 camshaft sprockets with washers and new locks finger tight ^ 1994-95 camshaft sprockets with taper lock rings finger tight 2. Timing belt in a counterclockwise direction around the sprockets. IMPORTANT: Make sure timing belt teeth are fully engaged […] Continue Reading

Comments (0)

Chevrolet

2004 Truck S10/T10 Distributor Removal & Installation

Posted on 18 November 2014

Download 2004 Truck S10/T10 Distributor Removal & Installation – INSTALLATION PROCEDURE 1. If installing a new distributor assembly, place 2 marks on the new distributor housing in the same location as the 2 marks on the original housing. 2. Remove the new distributor cap, if necessary. 3. Align the rotor with the second mark (2). […] Continue Reading

Comments (0)

Chevrolet

2008 Truck Silverado Fan Clutch Removal & Installation

Posted on 18 November 2014

Download 2008 Truck Silverado Fan Clutch Removal & Installation – Installation Procedure 1. Install the fan clutch bolts from the rear of the fan blade. 2. Notice: Refer to Fastener Notice in Service Precautions. Install the fan clutch bolts. Tighten the bolts to 23 Nm (17 ft. lbs.). 3. Install the fan assembly. 4. Install […] Continue Reading

Comments (0)

Ford

2005 Ford Focus Supercharger Removal & Installation

Posted on 17 November 2014

Download 2005 Ford Focus Supercharger Removal & Installation – Follow the instruction STEP-BY-STEP, and your installation will be trouble free. If in doubt, CALL! It is also suggested that as you proceed through the installation you read a few steps ahead so that you are sure to catch all notes and hints. During this installation […] Continue Reading

Comments Off

Ford

Transmission Position Switch/Sensor 08 Truck Ranger 2WD

Posted on 17 November 2014

Download Transmission Position Switch/Sensor 08 Truck Ranger 2WD – Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the […] Continue Reading

Comments Off

Chevrolet

2001 Truck Venture Intake Manifold Removal & Installlation

Posted on 16 November 2014

Download 2001 Truck Venture Intake Manifold Removal & Installlation – INSTALLATION PROCEDURE 1. If removed, install the thermostat. 2. If removed, install the water outlet. 3. Install the water outlet bolts. ^ Tighten the water outlet bolts to 25 Nm (18 ft. lbs.). 4. If removed, install the Engine Coolant Temperature (ECT) sensor ^ Tighten […] Continue Reading

Comments Off

SEE MORE ARTICLES IN THE ARCHIVE

Advertise Here Advertise Here